巴西插脚

Equipment’s combined with two-pole plug (Class II) 10 A/250V a.c. (figure 13. NBR 14136: 2002)

Symbol	Requirement (mm)	Measured (mm)		Symbol	Requirement (mm)	Measured (mm)
B	25.5 - 26.5			J	3.95 – 4.05
C	90 ° - 92 °			K	10.0 – 11.0
D	R 5.0 – 6.0			L	19.0 – 19.7
E	35.0 – 36.0			N	1.0 max.
F	13.0 – 14.4			O	R 2.0 -2.5
G	18.8 – 19.2			④	> 3 mm
①	> 14 mm			⑤	See above
②	See above			⑥	See above
③	See above			⑦	See above

Note:

1 The sketches are not intended to govern design, except as regards the dimensions shown

2 Plugs can be rewirable or non-rewirable

Requirements:

① – The distance between the engagement face and the cord or cord guard, if any, shall be at least 14 mm

② – Within this distance, the outline shall be not smaller than the engagement face.

③ – Within this distance, the outline shall be not larger than the engagement face.

④ – Insulating sleeves on the current-carrying pins are optional If the insulating sleeves are separate parts, they shall enter the plug by at least 3mm measured from the engagement face.

⑤ – The external diameter of the insulating sleeves shall not be larger than the diameter of the uninsulated part of the pins.

⑥ – To avoid damage to shutters, the ends of the pins shall show neither sharp edges nor burrs. They shall be of rounded shape as shown.

⑦ – The angle of 90° represents the maximum permissible area for the orientation of the entry of the flexible cable or cord.

印度插脚：

Indian Plug Checking Worksheet

Dimension: mm

Symbol	Rated Current		Measured
	(   ) 6A	(   ) 16A
A	22.22±0.15	28.6±0.15
B	19.1±0.15	25.4±0.15
C	7.010-7.085	8.660-8.735
D	5.030-5.105	7.010-7.085
E	15.77-16.94	20.47-21.64
F	20.47-21.64	28.47-29.64
G1)	≥7.94	≥9.52

Note:

1.       “G” is the minimum distance between the pins and the periphery of the plug.

阿根廷插脚：

IRAM 2063 Plug (Class II, two-pole) Checking Worksheet

（IRAM 2063：1982 + Amd 1999）

Symbol	Requirement (mm)	Measured (mm)		Symbol	Requirement (mm)	Measured (mm)
A	8.0 min.			H	120±5°
B	7.92±0.1			I	13.72±0.1
C	7.92±0.1			J	6.25±0.1
D	6.86±0.1			K	6.25±0.1
E	6.86±0.1			L	1.55±0.07
F	60°			M	18.2±0.2
G	60°			N	Marked “N”	Yes / No

沙特插脚：

SASO Plug Checking Form according to Figure 1 of SASO 2203

Symbol	Requirement (mm)	Measured (mm)		Symbol	Requirement (mm)	Measured (mm)
A	--			K	1.57
B	50.8 max.			L	1.57
C	32.5 max.			M	17.2 – 18.2
D	11.1			N	22.2-23.2
E	11.1			O	3.89 － 4.05
F	R 15 min.	Check by gauge		P	1.57
G	3.89 － 4.05			Q	3.89 － 4.05
H	6.22 － 6.48			R	R 9.5 min
I	6.22 － 6.48			S	R 9.5 min
J	1.57